Home Page Forums Raspberry Pi Shields NB_IOT Shield BG96

This topic contains 1 reply, has 2 voices, and was last updated by  Saeed 15 hours, 10 minutes ago.

Viewing 2 posts - 1 through 2 (of 2 total)
  • Author
    Posts
  • #37358

    danishshakil
    Participant

    My network is Band 28 LTE only network. I have checked traces on network side, UE is not sending any attach request.
    How can I make sure device is able to see my network.

    [email protected]:~ $ sudo pon
    pppd options in effect:
    debug # (from /etc/ppp/peers/provider)
    updetach # (from /etc/ppp/peers/provider)
    dump # (from /etc/ppp/peers/provider)
    noauth # (from /etc/ppp/peers/provider)
    remotename 3gppp # (from /etc/ppp/peers/provider)
    /dev/ttyUSB3 # (from /etc/ppp/peers/provider)
    115200 # (from /etc/ppp/peers/provider)
    lock # (from /etc/ppp/peers/provider)
    connect chat -s -v -f /etc/chatscripts/chat-connect -T internet # (from /etc/ppp/peers/provider)
    disconnect chat -s -v -f /etc/chatscripts/chat-disconnect # (from /etc/ppp/peers/provider)
    nocrtscts # (from /etc/ppp/peers/provider)
    modem # (from /etc/ppp/peers/provider)
    asyncmap 0 # (from /etc/ppp/options)
    lcp-echo-failure 4 # (from /etc/ppp/options)
    lcp-echo-interval 30 # (from /etc/ppp/options)
    hide-password # (from /etc/ppp/peers/provider)
    novj # (from /etc/ppp/peers/provider)
    novjccomp # (from /etc/ppp/peers/provider)
    ipcp-accept-local # (from /etc/ppp/peers/provider)
    ipcp-accept-remote # (from /etc/ppp/peers/provider)
    ipparam 3gppp # (from /etc/ppp/peers/provider)
    noipdefault # (from /etc/ppp/peers/provider)
    ipcp-max-failure 30 # (from /etc/ppp/peers/provider)
    defaultroute # (from /etc/ppp/peers/provider)
    usepeerdns # (from /etc/ppp/peers/provider)
    noccp # (from /etc/ppp/peers/provider)
    noipx # (from /etc/ppp/options)
    abort on (BUSY)
    abort on (NO CARRIER)
    abort on (NO DIALTONE)
    abort on (ERROR)
    abort on (NO ANSWER)
    timeout set to 30 seconds
    send (AT^M)
    expect (OK)
    ^M
    OK
    — got it

    send (ATE0^M)
    expect (OK)
    ^M
    ^M
    OK
    — got it

    send (ATI;+CSUB;+CSQ;+COPS?;+CGREG?;&D2^M)
    expect (OK)
    ^M
    ^M
    Quectel^M
    BG96^M
    Revision: BG96MAR02A07M1G^M
    ^M
    SubEdition: V08^M
    ^M
    +CSQ: 99,99^M
    ^M
    +COPS: 0^M
    ^M
    +CGREG: 0,2^M
    ^M
    OK
    — got it

    send (AT+CGDCONT=1,”IP”,”internet”,,0,0^M)
    expect (OK)
    ^M
    ^M
    OK
    — got it

    send (AT+QCFG=”nwscanseq”,01,1^M)
    expect (OK)
    ^M
    ^M
    OK
    — got it

    send (AT+QCFG=”nwscanmode”,1,1^M)
    expect (OK)
    ^M
    ^M
    OK
    — got it

    send (AT+QCFG=”iotopmode”,2,1^M)
    expect (OK)
    ^M
    ^M
    OK
    — got it

    send (ATD*99#^M)
    expect (CONNECT)
    ^M
    ^M
    CONNECT
    — got it

    Script chat -s -v -f /etc/chatscripts/chat-connect -T internet finished (pid 1036), status = 0x0
    Serial connection established.
    using channel 2
    Using interface ppp0
    Connect: ppp0 <–> /dev/ttyUSB3
    sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0xfa610abc> <pcomp> <accomp>]
    rcvd [LCP ConfReq id=0x3 <asyncmap 0x0> <auth chap MD5> <magic 0xd60d101d> <pcomp> <accomp>]
    No auth is possible
    sent [LCP ConfRej id=0x3 <auth chap MD5>]
    rcvd [LCP ConfAck id=0x1 <asyncmap 0x0> <magic 0xfa610abc> <pcomp> <accomp>]
    rcvd [LCP ConfReq id=0x4 <asyncmap 0x0> <magic 0xd60d101d> <pcomp> <accomp>]
    sent [LCP ConfAck id=0x4 <asyncmap 0x0> <magic 0xd60d101d> <pcomp> <accomp>]
    sent [LCP EchoReq id=0x0 magic=0xfa610abc]
    sent [IPCP ConfReq id=0x1 <addr 0.0.0.0> <ms-dns1 0.0.0.0> <ms-dns2 0.0.0.0>]
    rcvd [LCP DiscReq id=0x5 magic=0xd60d101d]
    rcvd [LCP EchoRep id=0x0 magic=0xd60d101d fa 61 0a bc]
    rcvd [IPCP ConfNak id=0x1 <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>]
    sent [IPCP ConfReq id=0x2 <addr 0.0.0.0> <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>]
    rcvd [IPCP ConfNak id=0x2 <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>]
    sent [IPCP ConfReq id=0x3 <addr 0.0.0.0> <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>]
    rcvd [IPCP ConfNak id=0x3 <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>]
    sent [IPCP ConfReq id=0x4 <addr 0.0.0.0> <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>]
    rcvd [IPCP ConfNak id=0x4 <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>]
    sent [IPCP ConfReq id=0x5 <addr 0.0.0.0> <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>]
    rcvd [IPCP ConfNak id=0x5 <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>]
    sent [IPCP ConfReq id=0x6 <addr 0.0.0.0> <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>]
    rcvd [IPCP ConfNak id=0x6 <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>]
    sent [IPCP ConfReq id=0x7 <addr 0.0.0.0> <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>]
    rcvd [IPCP ConfNak id=0x7 <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>]
    sent [IPCP ConfReq id=0x8 <addr 0.0.0.0> <ms-dns1 10.11.12.13> <ms-dns2 10.11.12.14> <ms-wins 10.11.12.13> <ms-wins 10.11.12.14>]

    #37655

    Saeed
    Moderator

    There is an update in the PPP installer. Could you please reinstall it?

    Previous PPP installer connects to GSM network only.

Viewing 2 posts - 1 through 2 (of 2 total)

You must be logged in to reply to this topic.